1/10 1. scope of application these specifications are applied to the chip type led lamp , model cll253emc7l1c. 2. part code c l l 2 5 3 e m c 7 l 1 c c l l 2 5 3 e m c 7 l 1 c c l l 2 5 3 e m c 7 l 1 c c l l 2 5 3 e m c 7 l 1 c series l253e : white power led for general lighting. special specifications m : general color rendering index typ. 85 type. watt class c7 : 7 watt package. lighting color l1 : compliance with ansi c78.3772008, 3step macadam ellipse, correlated color temperature 3000k. symbol data sheet citiled name cll253emc7l1c citizen electronics co.,ltd. japan ref.ce-p991 03/11
2/10 3. outline drawing 4. performance ( 1 ) absolute maximum rating symbol unit power dissipation p d w forward current i f ma forward pulse current i fp ma *1 reverse current i r ma operating temperature t op c storage temperature t st c junction temperature tj max c *2 *1 forward current : duty<=1/10 , pulse width<=10msec *2 d.c. current : tj = tc + rjc p d pulse current : tj = tc + rjc pw(power dissipation / onepulse) duty symbol citizen electronics co.,ltd. japan 10.4490 700 30 ~ +85 150 40 ~ +100 data sheet parameter rating value 1 citiled name cll253emc7l1c anode cathode resin tc measurement point cathode mark marking 1 marking 2 it has a protection device built in as a protection circuit against static electricity. unit : mm tolerances unless otherwise specified : 0.3 protection device anode cathode marking 1 : serial no. marking 2 :e m 7 l 1 c color watt ra l1 7 : 7w m : typ.85 ref.ce-p991 03/11
3/10 ( 2 ) electrooptical characteristics ( tc=25 c ) symbol condition min. typ. max. unit v f i f =420ma 17.5 18.6 21.0 v v if=420ma 465 550 lm ra if=420ma 85 rjc junctioncase (3.0) c/w chromaticity coordinates ( condition : i f =420ma ,tc=25 c ) note: the tolerance of measurement at our tester is vf3% , v10% , chromaticity(x,y)0.005. symbol citiled name cll253emc7l1c citizen electronics co.,ltd. japan data sheet parameter thermal resistance forward voltage luminous flux general color rendering index reference (ansi c78.377) x y x y 0.4338 0.4030 center 0.4338 0.4030 (3045k) a 0.4562 0.4260 a 0.00834 b 0.4299 0.4165 b 0.00408 c 0.4147 0.3814 ? 53.17 d 0.4373 0.3893 *color region stay within macadam "3step" ellipse from the chromaticity center. *the chromaticity center refers to ansi c78.377:200 8. please refer to ansi c78.377 for the chromaticity center. * is the angle between the major axis of the ellip se and the xaxis, and a and b are the major and minor semiaxes of a n ellipse. (ref. iec 60081:1997 annexd) l1 color rank color rank l1 center oval parameter xy chartcie1931 0.38 0.39 0.40 0.41 0.42 0.43 0.41 0.42 0.43 0.44 0.45 0.46 x y color region color region (ansi) 2800k 3400k 3200k 3000k ref.ce-p991 03/11
4/10 5. characteristics ? forward current vs. forward voltage ? forward current vs. relative luminous flux ? forward current vs. chromaticity coordinate ? case temperature vs. chromaticity coordinate symbol citizen electronics co.,ltd. japan citiled name cll253emc7l1c data sheet 0.020 0.015 0.010 0.005 0.000 0.005 0.010 0.015 0.020 0 100 200 300 400 500 i f [ma] x, y x y 0% 20% 40% 60% 80% 100% 120% 140% 0 100 200 300 400 500 i f [ma] relative luminous flux [a.u.] 15.0 16.0 17.0 18.0 19.0 20.0 21.0 0 100 200 300 400 500 i f [ma] v f [v] 0.020 0.015 0.010 0.005 0.000 0.005 0.010 0.015 0.020 0 20 40 60 80 100 tc [c] x, y x y i f =420ma tc=25c tc=25c tc=25c ref.ce-p991 03/11
5/10 ? case temperature vs. forward voltage ? case temperature vs. relative luminous flux ? spectrum symbol citiled citizen electronics co.,ltd. japan ? case temperature vs. allowable forward current name cll253emc7l1c data sheet 15.0 16.0 17.0 18.0 19.0 20.0 21.0 0 20 40 60 80 100 tc [c] [v] 0% 20% 40% 60% 80% 100% 120% 0 20 40 60 80 100 tc [c] relative luminous flux [a.u.] 0% 20% 40% 60% 80% 100% 120% 350 450 550 650 750 850 [nm] relative emission intensity [a.u.] 0 100 200 300 400 500 0 25 50 75 100 125 150 tc [c] i f [ma] i f =420ma i f =420ma tc=25c, if=420ma ref.ce-p991 03/11
6/10 6. reliability (1) details of the tests (2) judgment criteria of failure for reliability test (ta=25 c) symbol v f v u defines the upper limit of the specified characteristics. s defines the initial value. cll251mc4l reliability test results will be used for cll253emc7l1c. symbol data sheet judgment criteria for failure citiled name cll253emc7l1c citizen electronics co.,ltd. japan note: measurement shall be taken between 2 hours and 24 hours, and the test pieces should be i f =480ma 40 c 30 minutes C 100 c 30 minutes, 100 cycle > u 1.1 < s 0.85 returned to the normal ambient conditions after the completion of each test. total luminous flux measuring item forward voltage i f =480ma measuring condition test item test condition ta=25 c,i f =480 ma 1000 hours(with alfin) ta=50 c,i f =480 ma 1000 hours(with alfin) moistureproof test 60 c, 90 %rh for 1000 hours continuous operation test low temperature storage test 40 c 1000 hours high temperature storage test 100 c 1000 hours thermal shock test ref.ce-p991 03/11
7/10 7. packing specifications (1) packing an empty tray is placed on top of a fivetier tray which contain 48 pieces each. the set of six trays is banded together with two rubber bands. (smallest packing unit: 240 pieces) a label with product name, quantity, lot number is placed on the upper empty tray. tray (dimensions: 310 210 14.6mm / materials: electrically conductive ps) symbol name cll253emc7l1c data sheet citiled citizen electronics co.,ltd. japan < packing figure > product 50pcs/tray 310 210 14.6 product 48pcs/tray < example of indication label > 1. type e.g. cll253emc7l1c 2. p.no. (cutomer's p/n) e.g. xxx 3. lot no. e.g. 03d001 first letter: last digit of the year e.g. 0 : year 2010 second letter: production month e.g. 3 : m ar note: october, november and december are designated by x, y and z, respectively. third letter: ce's control number e.g. d001 4. quantity e.g. 240 pieces customer pass citizen electronics type p.no lot no q'ty CL-L253E-MC7L1-C xxx 03d001 240 pcs. (1) (2) (3) (4) ref.ce-p991 03/11
8/10 8. precautions 1. avoid the application of any stress to the resin portion. 2. avoid any contact by a sharp metal nail or other materials with the resin portion. 3. this product should be secured firmly by fastening an m3 screw on both sides of the product. please be careful not to apply any stress to the product during the clamping operation. please check thoroughly. 4. insulation between the terminal section and the heat sink section of the led is not covered by warranty. with regard to insulation after this product has been assembled in an apparatus, preventive action should be carried out by the customer. 5. for fixing this product to the outer heat sink, heat grease should be applied to the whole rear surface so that the product can dissipate heat as a whole. please pay attention to avoid product deformation when conducting the clamping operation with heat grease in sheet form. 6. handling of static electricity these products are sensitive to static electricity charge. please take measures to prevent any static electricity being produced such as the wearing of a wristband or antistatic gloves when handling this product. all devices, equipment and machinery must be properly grounded. it is recommended that precautions be taken against surge voltage to the equipment that mounts the leds. esd sensitivity of this product is 1000v (hbm, based on jeita ed4701/304). when inspecting the final products in which leds were assembled, it is recommended to check whether the assembled leds are damaged by static electricity or not. it is easy to find staticdamaged leds by a lighton test. symbol citiled name cll253emc7l1c citizen electronics co.,ltd. japan condition data sheet judgmental criterion as the connection status could vary depending on materials of outer heat sink, i f =7ma/pkg nolighting in entire block making up parallel circuit is unacceptable resin portion (shaded area) l251 consists of seven blocks. recommended installation screw pitch 13.08 mm 12.64 mm thermal conduction materials (insulation) outer heart sink spring washer ( Q 6mm) m3screw (insulation) plane washer ( Q 6mm) ref.ce-p991 03/11
9/10 8. precautions (continued) symbol name cll253emc7l1c citizen electronics co.,ltd. japan no external force shall be applied to resin part during soldering. soldering shall be implemented using a soldering bit of 40w or less with a temperature 350c or less within 3.5 seconds for one land. citiled taken into consideration, depending on ambient temperature (ta). manual soldering 11. recommended soldering condition (this product is not adaptable to reflow process) as this product is designed with consideration of the heat release property of module, a heat release design is required to use this product efficiently. factors responsible for an increase in temperature include heat generation attributed to (recommended condition in a case of leadfree solder condition) data sheet in assembled status. 9. drive circuit please ensure that heat generation is not in excess of the absolute maximum rating. (refer to 41 performance) 12. other this product complies with rohs directives. contacts number of soldering bit should be within twice for each terminal as a correction. * citizen electronics cannot guarantee if usage exceeds this recommended conditions. please use it after sufficient verification is carried out on your own risk if necessary. regarding soldering correction, above conditions shall be used. next process of soldering should be carried out after the product has returned to ambient a constant current circuit is recommended as a drive circuit. and when two or more led packages are connected, the series connection between each package is recommended. please design a circuit that prevents any reverse voltage (excess current) from being applied to this product instantaneously when the circuit is on or off. 10. heat generation ambient temperature conditions or power dissipation. thus, drive conditions should be for soldering correction 7. lighting at a low current a minimum current value of lighting of all dice is 35ma. when a minimum current is applied, led dice may look different in their brightness due to the individual difference of the led element, and it is not a failed product. 8. please be aware that this product should not come into contact with any other parts ref.ce-p991 03/11
10/10 such information, however, is subject to change without any prior notice. included in this document, business interruption and loss of data, and disclaims any and all express or implied warranties and for providing adequate designs and safeguards to minimize risk and avoid situations symbol 6. please contact citizen electronics' sales office if you have any questions regarding the information contained in this document, or if you have any other inquiries. citiled name cll253emc7l1c citizen electronics co.,ltd. japan data sheet and formal specifications must be exchanged and signed by both parties prior to mass production. 1. this document is provided for reference purposes only so that citizen electronics' 9. precautions with regard to product use products are used as intended. citizen electronics neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other a result of errors or omissions in the information included in this document. but citizen electronics assumes no liability whatsoever for any damages incurred as rights of citizen electronics or any third party with respect to the information before purchasing or using any citizen electronics' products listed in this document, in this document. 2. all information included in this document such as product data, diagrams, charts, is current as of the date this document is issued. 3. citizen electronics has used reasonable care in compiling the information please confirm the latest product information with a citizen electronics' sales office, 4. absent written signed agreement, except as provided in the relevant terms and conditions of or conditions of merchantability, fitness for a particular purpose, accuracy of information, and conditions related to sale, use of product, or information, including warranties or no infringement. citizen electronics assumes no liability for customers' product design or applications. bodily injury or damage to property, including data loss or corruption. in addition, customers are also responsible for determining the appropriateness of use of any information contained in this document such as application cases not only with evaluating by their own but also by the entire system. in which a malfunction or failure of a product could cause loss of human life, 5. though citizen electronics works continually to improve products' quality and reliability, sale for product, and to the maximum extent allowable by law, citizen electronics assumes no liability whatsoever, including without limitation, indirect, consequential, special, or incidental damages or loss, including without limitation, loss of profits, loss of opportunities, products can malfunction or fail. customers are responsible for complying with safety standards ref.ce-p991 03/11
|
